Production Intermediate

Recording acoustic guitar: microphone placement and technique

Where to place a microphone on an acoustic guitar, how room acoustics affect the result, and when to use a DI instead.

Short answer

The most reliable starting point for miking an acoustic guitar is a single small-diaphragm condenser microphone, aimed at the 12th fret from approximately 30–45 cm away. This position gives a balanced, natural sound. Avoid pointing the microphone at the soundhole — it produces excessive bass that is difficult to correct with EQ. The room matters: a hard-surfaced room adds unflattering early reflections; treating the recording position with soft furnishings or acoustic panels reduces this. For direct, clean recordings without room character (or when a good room is not available), a quality soundhole pickup or undersaddle transducer fed through a preamp or DI box is a practical alternative.

Microphone choice

Two types of microphone are well-suited to acoustic guitar:

  • Small-diaphragm condenser: the standard choice for acoustic guitar in professional studios. Fast transient response captures the attack of picked notes accurately. Good off-axis rejection helps with a controlled stereo image when using two mics. Requires phantom power (+48V) from your audio interface.
  • Large-diaphragm condenser: a common home studio choice because it is often the only condenser available. Sounds slightly warmer and richer than small-diaphragm; slightly less precise in transient detail. Works well for fingerpicking and singer-songwriter recordings where a warm, intimate character is desirable.

Dynamic microphones can be used for acoustic guitar but are less common — they have a slower transient response and are more suited to louder sources (electric guitar amps, drums). Ribbon microphones produce a warm, smooth sound that flatters acoustic guitar but require careful level management due to their lower output.

Microphone placement

The position of the microphone relative to the guitar determines the tonal balance:

  • 12th fret (standard position): 30–45 cm from the guitar, aimed at the point where the neck meets the body. Balanced bass, midrange and treble. The safest starting position for any style.
  • Upper bout (toward the neck): brighter, less bass. Useful for fingerpicking where clarity is important, or in a dense mix where low-mid build-up is a problem.
  • Lower bout (toward the body): warmer, fuller bass. Can sound boxy if overdone. More useful for strummed parts that need body and warmth.
  • Behind the bridge: captures the body resonance — useful as a second microphone blended with a 12th-fret mic for fullness.
  • Closer (10–20 cm): more direct, intimate sound; less room. Proximity effect adds bass on cardioid patterns — may need to be cut with EQ.
  • Further (60 cm+): more room character. Sounds natural and spacious in a good room; thin and reverberant in an untreated space.

Room acoustics and position

The room is part of the recording. In an untreated room with hard parallel walls (a typical bedroom or small home studio), early reflections from the walls colour the sound — particularly in the 200–400 Hz range, which adds a boxy, muddy quality to acoustic guitar.

Practical approaches for home recording:

  • Record in the corner of a room with soft furnishings nearby — bookshelves, a sofa, heavy curtains all absorb reflections.
  • Face away from the hardest wall surfaces when recording — this reduces the direct reflection from the wall behind you.
  • Use a closer mic position (20–30 cm) to capture more direct sound relative to room sound. This reduces the influence of room acoustics at the expense of natural ambience.
  • Record into a duvet or sleeping bag hung around the recording position — an effective DIY treatment for removing room reflections.

The home studio setup guide covers acoustic treatment in more detail.

Two-microphone techniques

Using two microphones gives a wider stereo image and allows blending two tonal perspectives:

  • XY stereo (coincident pair): two cardioid mics at 90° to each other, capsules as close as possible. Gives a narrow but phase-coherent stereo image — sums to mono without phase problems. Reliable and consistent.
  • Spaced pair (AB stereo): two mics separated by 30–60 cm, aimed at different areas (e.g. 12th fret and lower bout). Gives a wider, more open stereo image but can cause phase issues when summed to mono. Check by listening to a mono sum.
  • Mid-side (MS) stereo: a cardioid mic (mid) aimed directly at the guitar and a figure-8 mic (side) aimed across the guitar. Adjusting the level of the side mic controls stereo width. Fully mono-compatible. Requires a mid-side decoder (available in most DAWs as a utility).

When using two microphones, always check for phase coherence — flip the polarity of one mic and listen. If the guitar sounds thinner with the flip, the mics are in phase (good). If it sounds fuller with the flip, they are out of phase and need adjustment.

DI and pickup options

When a good recording space is not available, or when recording a live performance where microphone bleed is a problem, recording the guitar directly through a pickup or transducer is practical:

  • Undersaddle piezo transducer: built into many acoustic-electric guitars. Captures the string and saddle vibration directly — clean and consistent but lacks the body resonance of a microphone recording. Sounds direct and slightly clinical.
  • Soundhole magnetic pickup: electromagnetic pickup similar to an electric guitar humbucker, fitted in the soundhole. Warmer and more electric-guitar-like than a piezo. Loses some high-frequency detail.
  • Internal microphone systems: some acoustic-electric guitars have small internal microphones (e.g. K&K, Anthem) that capture more of the body resonance — the best-sounding DI option.

DI signals from pickups require a DI box or high-impedance instrument input on your audio interface to prevent signal loss and impedance mismatch. The audio interface guide covers instrument inputs and impedance.

Gain staging and levels

Acoustic guitar is a dynamic instrument — the difference between a gentle fingerpicked note and a hard strum can be 15–20 dB. Set the input gain so that the loudest strums peak around −12 to −6 dBFS on the DAW meter, leaving headroom for unexpected peaks. Recording too hot (peaks near 0 dBFS) risks digital clipping that cannot be recovered.

  • If using a condenser microphone, always enable phantom power (+48V) on your interface before connecting the mic.
  • Play the loudest passage the guitar part will contain before setting the gain level.
  • A light high-pass filter (80–100 Hz) in the DAW after recording removes low rumble and proximity effect bass build-up without affecting the guitar tone.

For EQ and processing after recording, the EQ basics guide covers frequency-specific adjustments for acoustic instruments.

Quick setup check: before pressing record, sit with the guitar in the position you will play, arm the track, play a loud strum, and confirm the meter peaks between −12 and −6 dBFS. Then play softly and confirm the quieter passages are still visible on the meter. If not, the dynamic range is too wide — consider light compression on the way in, or plan for more compression in post.

Next step

Recording acoustic guitar well starts with the right gear — the audio interface guide covers the input stage your microphone connects to. Once recorded, the EQ basics guide covers how to shape the recorded sound, and the reverb and space guide explains how to place the guitar in the mix. For in-depth microphone technique, the Sound On Sound magazine archive contains hundreds of detailed recording technique articles. The Audio Engineering Society publishes peer-reviewed research on microphone placement and room acoustics.

Frequently asked questions