Cables and connectors: XLR, TRS, TS, MIDI and USB — what goes where
The connectors used in music production — what each type carries, which to use in each situation, and how to avoid common wiring mistakes.
Short answer
Studio cabling uses a small set of connector types, each suited to specific signals and distances. XLR (three-pin, balanced) carries microphone signals and balanced line-level audio over long runs. TRS (three-conductor jack, balanced) carries balanced line-level or stereo headphone signals. TS (two-conductor jack, unbalanced) carries instrument-level signals — guitar and bass direct. RCA carries consumer line-level audio (CD players, home studio monitors). MIDI (originally 5-pin DIN, now often USB or TRS-MIDI) carries performance data, not audio. USB connects audio interfaces, MIDI controllers and some instruments to computers. Knowing which connector to use where eliminates the most common home studio wiring mistakes.
XLR
XLR is a three-pin professional audio connector. The three pins carry: positive signal (+), negative signal (−) and ground (shield). This three-conductor arrangement produces a balanced signal — inherently resistant to interference and suitable for long cable runs (20 metres and beyond without signal degradation).
- Microphone to audio interface: the primary use. All professional microphones (dynamic, condenser, ribbon) use XLR male connectors; audio interface microphone inputs use XLR female. The interface provides phantom power (+48V) through the same XLR cable for condenser microphones.
- Line-level balanced connections: between professional audio equipment — mixers, preamps, outboard processing, powered studio monitors with balanced inputs.
- Stage boxes and snake cables: multiple XLR lines bundled together for live performance, running from the stage to the front-of-house mixing desk.
The microphone types guide covers phantom power and the XLR input requirements for condenser and ribbon microphones.
TRS and TS (jack cables)
Both TRS and TS use the familiar 6.35 mm (¼ inch) jack plug — the standard instrument and studio connector. They look similar but carry different signals:
- TS (Tip-Sleeve, two conductors, unbalanced): carries a mono instrument-level or line-level signal. The tip carries the signal; the sleeve is the ground. Used for: electric guitar to amplifier, bass guitar to amplifier, guitar to audio interface Hi-Z input. Cable runs should be kept short (under 6 metres) — longer runs pick up hum and buzz.
- TRS (Tip-Ring-Sleeve, three conductors, balanced): carries either a balanced mono signal (for line-level connections between professional equipment) or a stereo unbalanced signal (for headphones). The additional "Ring" conductor enables balanced operation on the same jack size as TS. Used for: balanced insert connections on mixing desks, balanced monitor output connections, headphone outputs.
The 3.5 mm (⅛ inch) mini-jack version of TRS is used in consumer headphones, laptops and mobile devices. Many audio interfaces include a 3.5 mm headphone output.
RCA and other analogue connectors
- RCA (phono): the red-and-white consumer audio connector found on CD players, turntables, consumer receivers and some studio monitors with consumer inputs. Carries unbalanced line-level signals. Common in home studios when connecting consumer equipment to professional gear (often via an RCA-to-TRS adapter cable).
- Speakon: a locking connector used for high-power speaker connections between power amplifiers and passive PA speakers. Not used in home studios but common in live sound. Never use TS instrument cables to connect power amplifiers to speakers — the current levels can damage the cable and create a fire risk.
- Bantam/TT (Tiny Telephone): a smaller version of the jack connector used in professional patch bays — the panels that allow flexible routing between studio equipment. Patch bays are an intermediate and professional-level topic beyond the scope of a beginner home studio.
Digital connections: MIDI, USB, Thunderbolt
- MIDI (Musical Instrument Digital Interface): a protocol for transmitting musical performance data — note on/off, pitch, velocity, controller values, clock synchronisation. MIDI carries no audio. The original 5-pin DIN connector is still common on synthesisers, keyboards and interfaces. Many modern devices use USB-MIDI (the interface connects to the computer via USB and the DAW communicates with it via MIDI over that connection).
- USB: the most common connection between audio interfaces, MIDI controllers, electronic instruments and computers. USB audio interfaces vary in quality — the USB connection itself does not limit audio quality, but the interface's internal converters and preamps do. USB-A (rectangular), USB-C (oval, newer) and USB-B (square, common on older interfaces) are the three main connector shapes.
- Thunderbolt: a higher-bandwidth connection used by professional audio interfaces requiring very low latency or many simultaneous channels. Thunderbolt interfaces are more expensive than USB equivalents and require a Mac or PC with a Thunderbolt port.
- S/PDIF and ADAT optical (TOSLINK): digital audio connections that transfer multiple audio channels between devices — used to expand the input count of an audio interface by connecting an additional preamp or converter via ADAT optical (up to eight channels at 48 kHz).
Common studio wiring setups
A basic home studio with an audio interface:
- Microphone → XLR cable → audio interface XLR/mic input (with phantom power enabled for condensers).
- Electric guitar/bass → TS instrument cable → audio interface Hi-Z (instrument) input.
- Audio interface → USB cable → computer.
- Audio interface monitor output (TRS balanced or XLR) → studio monitors.
- Audio interface headphone output (TRS 6.35 mm) → headphones.
- MIDI keyboard → USB → computer (if USB-MIDI); or MIDI keyboard MIDI OUT → MIDI cable → audio interface MIDI IN → computer.
The audio interface guide covers input types and the full signal chain. The home studio setup guide covers laying out a working studio from scratch.
Next step
The audio interface guide covers how the interface connects all these cables into a working recording chain. The microphone types guide covers XLR inputs, phantom power and preamp requirements in more detail. The studio monitors guide covers balanced monitor connections and placement. The home studio setup guide brings all the components together into a complete working environment. For specific interface and cable compatibility questions, the manufacturer's technical documentation and the Sound On Sound Techniques section are reliable technical resources.
Frequently asked questions
A balanced audio connection uses three conductors (positive signal, negative signal, ground) to carry audio. The destination device reverses the polarity of the negative signal and combines it with the positive signal — any interference (hum, buzz, radio frequency) picked up along the cable is common to both conductors and cancels out when they are combined. An unbalanced connection uses only two conductors (signal and ground) and does not cancel interference. Balanced connections (XLR, TRS) are used for runs longer than approximately 5 metres or in environments with electrical interference. Short unbalanced runs (TS, RCA) are fine in a home studio with good electrical quality.
No. Microphones use XLR connectors. You cannot reliably connect an XLR microphone to a TS jack input even with an adapter — the impedance levels are different, the cable is unbalanced, and condenser microphones require phantom power that a TS input cannot provide. A microphone must be connected to an XLR input on an audio interface or mixing desk. The only exception is some dynamic microphones designed with a TS output for specific applications — check the microphone's specification.
Check in this order: (1) Try a different USB cable — USB cables fail silently and are a very common cause of connection problems. (2) Try a different USB port on the computer — some USB ports provide less power than others. (3) Check that the correct driver is installed (if the interface requires one — many USB audio interfaces on macOS do not need a separate driver). (4) Restart the computer and interface. (5) Check the interface manufacturer's website for known compatibility issues with your operating system version.
Impedance is the resistance a component presents to an alternating current — measured in ohms (Ω). For audio connections to work correctly, the output impedance of one device must be compatible with the input impedance of the next. Microphone outputs have very low impedance (typically 50–600Ω); microphone preamp inputs have high impedance (typically 1kΩ–5kΩ) to accept that signal. Instrument-level sources (guitar pickups) have high output impedance (typically 5kΩ–100kΩ) and require a high-impedance "Hi-Z" or instrument input. Connecting a high-impedance guitar directly to a low-impedance line input produces a thin, weak sound with poor bass response.